24 Valve Mild Street 182/214 Camshaft Combo


SKU: 07-c-24vc182 Categories: , Tag:


What’s included:

  • 182/214 Camshaft (fits 89-2018 Cummins)
  • Heavy duty pushrods (500-750 hp)
  • 103 Valve Springs
  • Lifters/tappets


  • RPM Range: 1400-3400
  • Drops EGT 200-300
  • Increased fuel economy 2-3 mpg
  • Quicker spool up
  • Increased bottom-mid range power
  • Duration at .050″ of lift  182 Intake, 214 Exhaust
  • Valve springs are meant to prevent valve float and improve overall performance
  • Heavy duty pushrods prevent bends or buckles up to 750hp

Modification Required:

  • For it to be “drop in” on a 12v you will need no more than .025″ piston protrusion and at least .055″ valve face depth with a standard head gasket and a 99 intake centerline. On a 98 – 02 24v you will need no more than .025″ piston protrusion and at least .038″ valve face depth with a standard gasket. On an 03 and up, it needs .018″piston protrusion and at least .038″ valve face depth with a standard gasket.  If you do not meet the minimum requirements for piston to valve clearance, don’t worry, you can still run an oversize head gasket or cut valve reliefs.
  • Although this is considered a drop in cam it is important to check clearances (You can use our clearance calculator to make it a little easier)
  • We always recommend new lifters when changing a cam.



  • Used in daily drivers
  • Smaller single, or set of compounds
  • Weekend warrior
  • Towing


Break in:

To make sure that you have no issues during break-in, follow these few suggestions.

  • Make sure that the cam has a Liberal amount of quality assembly lube applied
  • DO NOT let the engine start without oil pressure
  • When this is a new engine, be sure to put a liberal amount of assembly lube in the oil pump and prime the oil filter
  • Be sure to change the oil after you have done your break-in procedure. When the filter and oil system are already primed, engine will get oil pressure much faster than if the oil is changed at the same time.
  • Disconnect the fuel system and spin the engine with the starter until oil pressure can be read or until oil is coming out of the rocker arms.
  • Do not let the starter run for more than 10 seconds at a time
  • Once oil pressure has been verified, let the engine start and run for five minutes at 1200-1500rpm then shut engine down
  • Adjust valves then you are cleared to abuse your engine. Enjoy the added airflow
  • if you need to re-torque or “hot-torque “the head, do so before adjusting valves. Re-torqueing the head changes the valve lash setting, so it is important to set lash last.

Cam Info:

Cam Lift0.3000182.0-
Valve Lift0.4140182.0-
Cam Lift0.3200214.044.0-10.0117.00.0240
Valve Lift0.4288214.044.0-10.0117.00.0320

Additional information


24 Valve Cummins

Valve Springs

103 Valve Springs, Installed Height 1.380


Heavy Duty Pushrods, Good to 750 HP


1.45" Lifters


182/214 Mild street Cam, Meant for larger turbos towing/daily drivers


Cummins 6BT

Engine Year

1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019

Product Type

Camshaft & Accessories, Pushrod, Valve Springs

Cummins Cam Combos

Slide left and Right